Skip to main content

Hardware Details

NULA DeepSleep ESP32-S3 breaks out the ESP32-S3's GPIO pins on two rows of breadboard-compatible header holes, with power, reset and UART pins alongside. A Qwiic connector carries power and I2C (a two-wire bus for talking to chips) on one cable, so you can add a sensor without using header pins. The board also has a JST battery connector with an onboard charger, a PCF85063A real-time clock, a CH340K USB-to-serial chip, a USER button, a RESET button and an addressable RGB LED on IO2.

Top-down view of the NULA DeepSleep ESP32-S3 with callouts for the ESP32-S3 module, the CH340K USB-to-serial chip, the TP4056M charger, the JST battery connector with charging, the Qwiic connector, and the USB-C connector for programming and charging
NULA DeepSleep ESP32-S3 main components

Pinout​

NULA DeepSleep ESP32-S3 pinout diagram: two rows of header pins labelled IO0 to IO48 with their SPI, I2C, ADC and PWM functions, RXD0 and TXD0 UART pins, a RESET, 3V3, GND, VCC and BAT power block, the JST battery connector, USER and RESET buttons, the Qwiic connector, the WS2812B LED on IO2, and a note that JP1 disconnects the WS2812B LED power supply
NULA DeepSleep ESP32-S3 pinout

Pin details​

Pin markingPin nameDescription
RXDRXD0UART receive (GPIO44)
TXDTXD0UART transmit (GPIO43)
13IO13Digital I/O, SPI MISO (FSPI MISO), ADC input, PWM
11IO11Digital I/O, SPI MOSI (FSPI MOSI), ADC input, PWM
12IO12Digital I/O, SPI clock (FSPI CLK), ADC input, PWM
10IO10Digital I/O, SPI chip select (FSPI CS), ADC input, PWM
4IO4Digital I/O, ADC input, PWM
5IO5Digital I/O, ADC input, PWM
IO6IO6Digital I/O, ADC input, PWM
IO7IO7Digital I/O, ADC input, PWM
RESETRESETControl pin, resets the board
3V33V3Power supply pin, 3.3 V
GND (left row)GroundGround reference
VCCVCCPower supply pin
BATBATPower supply pin, battery
8IO8Digital I/O, I2C data (SDA), ADC input, PWM
9IO9Digital I/O, I2C clock (SCL), ADC input, PWM
42IO42Digital I/O, PWM
41IO41Digital I/O, PWM
40IO40Digital I/O, PWM
39IO39Digital I/O, PWM
38IO38Digital I/O, PWM
0IO0Digital I/O, strapping pin (it sets the boot mode at reset), also wired to the USER button
IO48IO48Digital I/O, PWM
IO47IO47Digital I/O, PWM
IO21IO21Digital I/O, PWM
IO14IO14Digital I/O, ADC input, PWM
IO19IO19Digital I/O, ADC input, PWM
IO20IO20Digital I/O, ADC input, PWM
GND (right row)GroundGround reference

Some GPIOs are not on a header. IO2 drives the onboard WS2812B RGB LED, and IO17 receives the real-time clock's interrupt output. The USER button pulls IO0 low and the RESET button pulls EN low. Three small LEDs show activity: red for charging (CHRG), blue for TXD0 and white for RXD0.

Power supply​

Power the board over USB-C, which also programs it through the CH340K. A 500 mA fuse protects the USB input. For battery projects, plug a Li-Ion or Li-Po battery into the 2-pin JST connector. The onboard TP4056M charger charges it from USB, and the board picks USB or the battery as its power source on its own. A TPS7A2633 regulator makes the 3.3 V rail, and the board's logic is 3.3 V. Check the battery connector's polarity against the marking on the board before you plug a battery in. The charging current is set by a 3 kΩ resistor on the charger's PROG pin, which gives about 400 mA.

Real-time clock and I2C​

The PCF85063A real-time clock (RTC) sits on the same I2C bus as the Qwiic connector, at address 0x51. A 32.768 kHz crystal keeps its time. The bus has 4.7 kΩ pull-up resistors to 3.3 V on SDA and SCL, so a Qwiic sensor needs none of its own.

Dimensions​

  • Board size: 63 × 26 mm, 7.2 mm high
  • Header spacing: the two header rows are 22.86 mm (0.9 in) apart, so the board is breadboard-compatible. Header pins are included but unsoldered.
  • Mounting: one 3.2 mm diameter mounting hole, between the USER and RESET buttons
NULA DeepSleep ESP32-S3 at an angle inside a bounding box with its dimensions: 63 mm long, 26 mm wide and 7.2 mm high, and a callout for the 3.2 mm diameter mounting hole beside the USER button
NULA DeepSleep ESP32-S3 dimensions

Jumpers​

NULA DeepSleep ESP32-S3 pinout diagram, top-left corner, showing the note: JP1 (NC) disconnects the WS2812B LED power supply
NULA DeepSleep ESP32-S3 jumpers
JumperDefaultFunction
JP1Connected (NC, normally closed)Cut to disconnect the WS2812B RGB LED from VCC

With JP1 cut, the onboard LED stays dark and the Quick Start Blink example shows nothing.