Brojač koraka

Što prikazuje ovaj primjer

Brojanje koraka pomoću ugrađenog brojača koraka čipa BMA400, koji također javlja hodate li, trčite ili mirujete. Čip sam detektira i broji korake; pri koraku postavlja INT1, a vaš kontroler čita broj koraka.

Osim Qwiic konektora ili I2C pinova headera, spojite INT1 pin pločice na digitalni pin 2 na vašem kontroleru ili u skici promijenite interruptPin na pin koji koristite. Pin mora podržavati prekide.

Primjer koda

Select Board

stepCounter.ino

/**
 **************************************************
 *
 * @file        stepCounter.ino
 *
 * @brief       Example showing how to use the BMA400's built-in step
 *              counter and activity type detection (running/walking/still)
 *
 * @link        solde.red/333419 : Soldered BMA400 Accelerometer breakout
 *
 * @authors     SparkFun Electronics, modified by Soldered Electronics
 ***************************************************/
#include <BMA400-SOLDERED.h>

// Create an instance of the BMA400 sensor
Soldered_BMA400 accelerometer;

// Pin connected to the sensor's INT1 pin, change to match your wiring
int interruptPin = 2;

// Flag to know when an interrupt occurs
volatile bool interruptOccurred = false;

void bma400InterruptHandler()
{
    interruptOccurred = true;
}

void setup()
{
    // Initialize serial for output
    Serial.begin(115200);
    Serial.println("BMA400 Example - Step Counter");

    // Initialize I2C bus
    Wire.begin();

    // Check if sensor is connected and initialize it.
    // Address is optional, defaults to 0x14
    while (accelerometer.begin() != BMA400_OK)
    {
        Serial.println("Error: BMA400 not connected, check wiring and I2C address!");
        delay(1000);
    }

    Serial.println("BMA400 connected!");

    // Configure the step counter feature. Step detection and counting is
    // handled entirely by the sensor; the count is a 24-bit value that can
    // be read at any time
    bma400_step_int_conf config = {
        .int_chan = BMA400_INT_CHANNEL_1 // Route interrupt to INT1 pin
    };
    accelerometer.setStepCounterInterrupt(&config);

    // Configure INT1 pin to push/pull mode, active high
    accelerometer.setInterruptPinMode(BMA400_INT_CHANNEL_1, BMA400_INT_PUSH_PULL_ACTIVE_1);

    // Enable the step counter interrupt condition. This must be enabled for
    // step counting to work at all, even without using the interrupt pin
    accelerometer.enableInterrupt(BMA400_STEP_COUNTER_INT_EN, true);

    // Attach the interrupt handler to the microcontroller pin wired to INT1
    attachInterrupt(digitalPinToInterrupt(interruptPin), bma400InterruptHandler, RISING);
}

void loop()
{
    if (interruptOccurred)
    {
        interruptOccurred = false;

        // Check which interrupt condition triggered
        uint16_t interruptStatus = 0;
        accelerometer.getInterruptStatus(&interruptStatus);

        if (interruptStatus & BMA400_ASSERTED_STEP_INT)
        {
            // Get total step count and detected activity type
            uint32_t stepCount = 0;
            uint8_t activityType = 0;
            accelerometer.getStepCount(&stepCount, &activityType);

            Serial.print("Step detected! Step count: ");
            Serial.print(stepCount);
            Serial.print("\t");

            Serial.print("Detected activity: ");
            switch (activityType)
            {
            case BMA400_RUN_ACT:
                Serial.println("Running");
                break;
            case BMA400_WALK_ACT:
                Serial.println("Walking");
                break;
            case BMA400_STILL_ACT:
                Serial.println("Standing still");
                break;
            default:
                Serial.println("Unknown");
                break;
            }
        }
    }
}

Ovaj primjer koristi i attachInterrupt() i digitalPinToInterrupt() (Arduino referenca), koje dolaze s Arduino jezgrom i nisu dio biblioteke Soldered BMA400 Accelerometer.

Očekivani rezultat:

Serial MonitorAutoscrollShow timestampNewline115200 baud

Message (Enter to send message to the board)

BMA400 Example - Step Counter
BMA400 connected!

Nakon pokretanja, svaki prekid zbog koraka ispisuje jedan redak: Step detected! Step count: s ukupnim brojem koraka, tabulator, zatim Detected activity: iza čega slijedi Running, Walking, Standing still ili Unknown.

Korištene funkcije

Soldered_BMA400()returns none

Konstruktor. Stvara objekt senzora; ne komunicira sa senzorom dok ne pozovete begin().

ReturnsKonstruktor; nema povratne vrijednosti.

int8_t begin(uint8_t address = BMA400_I2C_ADDRESS_DEFAULT, TwoWire &wirePort = Wire)returns int8_t

Pokreće senzor preko I2C-a: softverski resetira BMA400, provjerava ID čipa i postavlja ga u normalni način rada.

ReturnsBMA400_OK (0) u slučaju uspjeha, inače negativan kod pogreške. Adresa različita od 0x14 ili 0x15 vraća BMA400_E_INVALID_CONFIG.

Parametri

Tip	Naziv	Opis
`uint8_t`	`address`	I2C adresa. `BMA400_I2C_ADDRESS_DEFAULT` (`0x14`, zadano) ili `BMA400_I2C_ADDRESS_SECONDARY` (`0x15`).
`TwoWire &`	`wirePort`	I2C sabirnica koja se koristi. Zadano je `Wire`.

int8_t setStepCounterInterrupt(bma400_step_int_conf* config)returns int8_t

Određuje na kojem pinu za prekid brojač koraka signalizira.