Hardware Details
The board carries an SGX-4CO electrochemical cell for carbon monoxide, a Texas Instruments LMP91000 analog front end that biases the cell and turns its current into a voltage, a 16-bit ADS1115 ADC, a 2.5 V voltage reference for the front end, and a Microchip ATtiny404 with factory firmware. The ATtiny404 is the only device on your I2C bus: it talks to the front end and the ADC over a second, internal bus. There is no regulator, so everything runs from the 3.3 V supply.
Key specifications
| Specification | Value |
|---|---|
| MCU | |
| Bridge MCU | Microchip ATtiny404, factory firmware |
| Interface | |
| Interface | I2C; analog and digital signals on the header |
| Qwiic compatible | Yes, 2 Qwiic connectors |
| Default I2C address | 0x30 |
| I2C address changeable | Yes, 0x30 to 0x37 with the three-switch ADDRESS DIP switch |
| Header pins | VOUT (analog out), ALERT, AIN1 to AIN3 (analog in) |
| Breadboard compatible | No |
| Measurement | |
| Measurement types | Gas: carbon monoxide (CO) |
| Measurement range | 0 to 1000 ppm CO (SGX-4CO); maximum overload 2000 ppm |
| Measurement accuracy | Linearity within ±5%; zero shift under ±12 ppm equivalent (-40 to +50 °C); the store record gives no repeatability or resolution |
| Response time | T90 under 30 s |
| Power | |
| Supply voltage | 3.3 V, no regulator; the Qwiic connectors share this supply |
| Logic level | 3.3 V only |
| Other | |
| Gas cell | SGX-4CO, electrochemical |
| Analog front end | Texas Instruments LMP91000 |
| ADC | Texas Instruments ADS1115, 16-bit |
| Operating conditions | -30 to 50 °C, 15 to 90% RH (non-condensing) |
| Dimensions | 38 x 38 mm |
| Mounting holes | 4 x 3.2 mm |
Pinout
| Pin marking | Pin name | Description |
|---|---|---|
| GND | Ground | Ground. Two on the top header, two on the bottom header, one on the side header. |
| 3V3 | Supply | 3.3 V supply. Two on the top header, one on the side header; all are the same net as the Qwiic connectors' supply. |
| SDA1 | I2C data | Your controller's I2C data line, the same line as on the Qwiic connectors. Pulled up to 3V3 through 10 kΩ (JP5). |
| SCL1 | I2C clock | Your controller's I2C clock line, the same line as on the Qwiic connectors. Pulled up to 3V3 through 10 kΩ (JP5). |
| SDA2 | Internal I2C data | The internal bus between the ATtiny404, the LMP91000 and the ADS1115. Pulled up to 3V3 through 10 kΩ (JP6). |
| SCL2 | Internal I2C clock | The internal bus clock. Pulled up to 3V3 through 10 kΩ (JP6). |
| VOUT | Analog output | The LMP91000's output voltage, the signal the ADS1115 converts. Also wired to the ATtiny404. |
| ALERT | ADC alert | The ADS1115's ALERT pin, also wired to the ATtiny404. |
| LMPEN | Front-end enable | The LMP91000's enable input (MENB), pulled to GND through 10 kΩ and also wired to the ATtiny404. Leave it unconnected for normal use. |
| AIN1 to AIN3 | Analog inputs | The ADS1115's other three inputs, for your own analog signals. The libraries read only the gas cell's channel and have no function for these inputs. |
| UPDI | Programming | The ATtiny404's UPDI programming pin, on the 3-pin side header with GND and 3V3. |
| Qwiic (x2) | Qwiic connectors | Plug-and-play I2C, each carrying 3V3, SDA1, SCL1 and GND. Either works; the other is free for the next Qwiic board. |
Voltage and logic levels
| Connection | Supported voltage | Notes |
|---|---|---|
3V3 supply | 3.3 V | No regulator. The header 3V3 pins and both Qwiic connectors share this one supply. |
| I2C and signal pins | 3.3 V logic | No level shifter. |
| Qwiic connectors | 3.3 V | Carry 3V3 along with I2C, so a Qwiic cable powers the board. |
Power the board from 3.3 V only and do not connect 5 V to 3V3 or to any
signal pin. The board has no regulator or level shifter.
Dimensions
The board is 38 x 38 mm, with four mounting holes of 3.2 mm diameter.
Jumpers

The I2C address is set with the three-switch ADDRESS DIP switch at the top left, not with a solder jumper. It gives addresses 0x30 to 0x37, and the board ships at 0x30. Give each board on the same bus its own address and pass that address to the library.
The solder jumpers are on the top of the board.
| Jumper | Default | Function |
|---|---|---|
| JP1 | Closed | Joins the analog ground (AGND) to GND. Cut it to separate them. |
| JP2 to JP4, ADC address | JP2 closed, JP3 and JP4 open | Set the ADS1115's address on the internal bus: JP2 ties its ADDR pin to 3V3 (0x49), JP3 to SDA2 (0x4A), JP4 to SCL2 (0x4B). This is not the board's address on your bus. |
| JP5, I2C pull-ups | Closed | Connects 10 kΩ pull-ups from 3V3 to SDA1 and SCL1. Cut it to disconnect them. |
| JP6, internal pull-ups | Closed | Connects 10 kΩ pull-ups from 3V3 to SDA2 and SCL2. Cut it to disconnect them. |
Use at most one of JP2, JP3 and JP4. Closing JP3 or JP4 while JP2 is closed
ties SDA2 or SCL2 straight to 3V3, so the internal bus line can no
longer be pulled low. Closing JP3 and JP4 together shorts SDA2 to SCL2.
