Skip to main content

Hardware Details

The board reads a 3-electrode SGX-4 series electrochemical gas cell. Three chips do the work:

  • the LMP91000 analog front end biases the cell and turns its current into a voltage, VOUT. Its bias, gain and load resistor are set over I2C;
  • the ADS1115, a 16-bit ADC, converts VOUT on its first input. Its other three inputs, AIN1 to AIN3, are on the header;
  • the ATtiny404, running factory firmware, configures the LMP91000 and reads the ADS1115 for you.

The LMP91000 datasheet describes the front end in full.

An MCP1525 gives the front end a 2.5 V reference. The cell sits on the underside of the board, with its three pins in the sockets around the centre of the top.

The board has two I2C buses. The first one, SDA1 and SCL1, is on both Qwiic connectors and the top header, and only the ATtiny404 is on it, at address 0x30 to 0x37: over Qwiic, your controller talks to this bridge (0x30 as shipped). The LMP91000 (0x48) and the ADS1115 (0x49 by default) sit on the second one, SDA2 and SCL2, which the ATtiny404 drives. The direct-address examples wire your controller to SDA2 and SCL2 on the header and address the ADS1115 and the LMP91000 directly.

Key specifications​

SpecificationValue
Interface
InterfaceI2C; analog VOUT, AIN1 to AIN3 and the ALERT and LMPEN signals on the header
Qwiic connectors2
Default I2C address0x30
I2C address range0x30 to 0x37, set with the three-position address switch
Breadboard compatibleNo
Measurement
Measurement typesGas
Gas cellSGX-4 series electrochemical cell, 3-electrode
Library presetsCO, NO2, SO2, O3, NO, H2S, NH3, Cl2
ADCTexas Instruments ADS1115, 16-bit, 4 inputs
Voltage referenceMCP1525, 2.5 V
Power
Supply voltage3.3 V, no regulator
Logic level3.3 V only
Other
Analog front endTexas Instruments LMP91000
Bridge MCUMicrochip ATtiny404, factory firmware
Connectors2x Qwiic, 2.54 mm headers
Dimensions38 x 38 mm
Mounting holes4x 3.2 mm

Pinout​

Pin markingPin nameDescription
3V3Supply3.3 V supply for the whole board. On the top header (twice) and the right header.
GNDGroundGround. On all three headers.
SDA1, SCL1Host I2CThe bus your controller uses, also on both Qwiic connectors. Only the ATtiny404 is on it. Pulled up to 3V3 through 10 kΩ (JP5).
SDA2, SCL2On-board I2CThe bus between the ATtiny404, the LMP91000 and the ADS1115. Pulled up to 3V3 through 10 kΩ (JP6). Not on the Qwiic connectors: the direct-address examples wire your controller here to address the ADS1115 and the LMP91000 directly.
VOUTFront-end outputThe LMP91000's output voltage, the signal the ADS1115 converts on its first input.
ALERTADC alertThe ADS1115's ALERT/RDY pin, also wired to the ATtiny404.
LMPENFront-end enableThe LMP91000's enable input (MENB), also wired to the ATtiny404. In bridge mode (0x30 to 0x37) the libraries do not drive it; the direct-address examples that pass a config pin wire it to that GPIO.
AIN1, AIN2, AIN3Analog inputsThe ADS1115's other three inputs, for your own analog signals. The Arduino and MicroPython libraries read only AIN0 (VOUT), so no library function reads these.
UPDIProgrammingThe ATtiny404's programming pin, on the right header.
Qwiic (x2)Qwiic connectorsEach carries 3V3, GND, SDA1 and SCL1. Either works; the other is free for the next Qwiic board.

Voltage and logic levels​

ConnectionSupported voltageNotes
3V3 supply3.3 VNo regulator. The header and both Qwiic connectors share this one supply.
I2C and signal pins3.3 V logicNo level shifter. Do not connect 5 V signals.
Qwiic connectors3.3 VCarry 3V3 along with I2C, so a Qwiic cable powers the board.

Do not connect 5 V to 3V3 or to any signal pin. The board has no regulator or level shifter.

Dimensions​

The board is 38 x 38 mm, with four mounting holes of 3.2 mm diameter.

Jumpers​

Top of the breakout: an ADDRESS DIP switch at the top left, Qwiic connectors on the left and right edges, three round cell sockets around the centre chip, jumpers JP1 to JP6, and labelled header rows along the top, bottom and right edges
Top: the ADDRESS switch at the top left, JP5 below it, JP1 left of centre, JP2 to JP4 right of centre, JP6 at the bottom right

The address switch sets the address your controller uses. The solder jumpers set things on the board's own side: ground, pull-ups and the ADS1115's address on the internal bus.

JumperDefaultFunction
ADDRESS switch (3 positions)0x30Sets the board's I2C address from 0x30 to 0x37, so up to eight boards share one bus. Pass the same address to the library.
JP1ClosedConnects the front end's analog ground (AGND) to GND. Cut it to separate them.
JP2 to JP4JP2 closed, JP3 and JP4 open: 0x49The ADS1115's address on the internal bus: JP2 ties ADDR to 3V3 (0x49), JP3 to SDA2 (0x4A), JP4 to SCL2 (0x4B). Open JP2 before closing JP3 or JP4, and close only one. Over Qwiic, the bridge reads the ADS1115 for you; the direct-address examples address it at this address on SDA2 and SCL2.
JP5Closed10 kΩ pull-ups from SDA1 and SCL1 to 3V3. Cut it to disconnect them.
JP6Closed10 kΩ pull-ups from SDA2 and SCL2 to 3V3.

Cut JP2 before you bridge JP3 or JP4. With JP2 still closed, JP3 ties SDA2 and JP4 ties SCL2 straight to 3V3. Never bridge JP3 and JP4 together: that ties SDA2 to SCL2. Either one stops the internal bus between the chips.