Quick Start
Connect the breakout over Qwiic, install the library, and run the library's example for this board. It finds the board at its default address, 0x30, sets up the analog front end and prints a reading every 2.5 seconds.
You program the controller connected to this breakout. The breakout itself is not flashed: its ATtiny404 comes with its firmware already on it.
The board runs from 3.3 V only. It has no regulator, so the header and both
Qwiic connectors share one 3.3 V supply. Do not connect 5 V to 3V3.
The libraries have no preset for this board's SGX-4OX-ROHS oxygen cell yet.
The examples below use a preset written for another gas (SENSOR_CO in
Arduino, SENSOR_O3 in MicroPython). They prove the connection and show the
reading format, but the value they print is calculated with that gas's
settings, not the oxygen cell's. The Arduino
and MicroPython
example pages explain what to change for the oxygen cell.
- Arduino
- MicroPython
1. Connect the breakout board
Plug a Qwiic cable into either Qwiic connector on the board and into the Qwiic
connector on your controller. Each Qwiic connector carries 3V3, SDA1,
SCL1 and GND, so the one cable powers the board and connects I2C.
| NULA DeepSleep | Soldered Electrochemical O2 Gas Sensor Breakout (Qwiic) |
|---|---|
| Qwiic connector | Qwiic connector |
Without Qwiic: breadboard wiring
Solder the included header pins and wire the top header's 3V3, GND,
SDA1 and SCL1 to your controller's 3.3 V supply, ground and I2C pins.
SDA1 and SCL1 are the same bus as the Qwiic connectors.
| NULA DeepSleep | Soldered Electrochemical O2 Gas Sensor Breakout (Qwiic) |
|---|---|
| GND | GND |
| 3V3 | 3V3 |
| IO8 | SDA1 |
| IO9 | SCL1 |
Leave SDA2 and SCL2 unconnected: they are the board's internal bus between
the ATtiny404 and the two analog chips.
2. Install the library
Install Electrochemical Gas Sensor Soldered from its GitHub repository.
🔗Soldered Electrochemical Gas Sensor Arduino library
Verified Arduino library at commit c4df54b
Tip: downloading from GitHub. On the library's GitHub page, click the green Code button and choose Download ZIP, then add it in Arduino IDE with Sketch → Include Library → Add .ZIP Library....
3. Run the first example
Open bridgeBoard from the library's examples, select your board and port, and upload it. The sketch creates the sensor at 0x30, the address this board answers on with the ADDRESS switch at its default.
Where the sketch's comments mention address jumpers on the back of the board, this board uses the three-position ADDRESS switch on its top side instead.
/**
**************************************************
*
* @file bridgeBoard.ino
* @brief See how to init a sensor on the new ATtiny404 bridge board revision,
*
* To successfully run the sketch:
* - Set the desired address using the jumpers on the back of the board
* (address = 0x30 + jumper offset, giving a range of 0x30-0x37)
* - Run the sketch and open serial monitor at 115200 baud!
*
* Note: on this board revision, LMPEN is hardwired to GND, so there's
* no configPin argument to pass - the constructor's third argument
* is ignored whenever the address falls in the bridge range (0x30-0x37).
*
*
* @authors @ soldered.com
***************************************************/
// Include the required library
#include "Electrochemical-Gas-Sensor-SOLDERED.h"
// Any additional boards on the same bus just need a different jumper setting
// (0x30-0x37), same as twoSensors.ino does for legacy boards with 0x49/0x4A/0x4B.
ElectrochemicalGasSensor sensor(SENSOR_CO, 0x30);
void setup()
{
Serial.begin(115200); // For debugging
// Init the breakout
if (!sensor.begin())
{
// Can't init? Notify the user and go to infinite loop
Serial.println("ERROR: Can't init the sensor! Check connections and jumper address!");
while (true)
delay(100);
}
Serial.println("Sensor initialized successfully!");
}
void loop()
{
// Make the reading
double reading = sensor.getPPM();
// If PPB is more relevant for your sensor, you can use:
// double reading = sensor.getPPB();
// Print the reading with 5 digits of precision
Serial.print("Sensor reading: ");
Serial.print(reading, 5);
Serial.println(" PPM");
// Wait a bit before reading again
delay(2500);
}
4. Check the result
Open the Serial Monitor at 115200 baud. When the board answers, the first line is:
Sensor initialized successfully!
After it, a line Sensor reading: followed by a value with five decimals and
PPM arrives every 2.5 seconds.
If you see ERROR: Can't init the sensor! Check connections and jumper address!
instead, the board did not answer at 0x30.
5. If it does not work
Continue with Troubleshooting and retry this smallest example after each change.
1. Connect the breakout board
The module's example opens I2C bus 0 with SCL on pin 22 and SDA on pin 21.
Change the pin numbers in the example if your controller's Qwiic connector or
the pins you wire are elsewhere.
Plug a Qwiic cable into either Qwiic connector on the board and into the Qwiic
connector on your controller. Each Qwiic connector carries 3V3, SDA1,
SCL1 and GND, so the one cable powers the board and connects I2C.
| NULA DeepSleep | Soldered Electrochemical O2 Gas Sensor Breakout (Qwiic) |
|---|---|
| Qwiic connector | Qwiic connector |
The example sets SDA to pin 21 and SCL to pin 22. On the NULA DeepSleep, change them to 8 (SDA) and 9 (SCL), the board's I2C pins shown in the diagram.
Without Qwiic: breadboard wiring
Solder the included header pins and wire the top header's SDA1 to IO8 and
SCL1 to IO9 on the NULA DeepSleep, then change the example's pins to 8 (SDA)
and 9 (SCL).
| NULA DeepSleep | Soldered Electrochemical O2 Gas Sensor Breakout (Qwiic) |
|---|---|
| GND | GND |
| 3V3 | 3V3 |
| IO8 | SDA1 |
| IO9 | SCL1 |
The example sets SDA to pin 21 and SCL to pin 22. On the NULA DeepSleep, change them to 8 (SDA) and 9 (SCL), the board's I2C pins shown in the diagram.
Leave SDA2 and SCL2 unconnected: they are the board's internal bus between
the ATtiny404 and the two analog chips.
2. Install the module
After installing the mpremote package, install the library on your board using the following command:
mpremote mip install github:SolderedElectronics/Soldered-ElectrochemicalGasSensor-MicroPython-Library
Or, if you're running a Windows OS:
python -m mpremote mip install github:SolderedElectronics/Soldered-ElectrochemicalGasSensor-MicroPython-Library
🔗Soldered Electrochemical Gas Sensor MicroPython library
Verified MicroPython module at commit 623e1e6
Tip: downloading from GitHub. Without mpremote, open the module's .py
file on GitHub and click Download raw file, then open it in Thonny and use
File → Save as... → MicroPython device to copy it onto the board. This
library has three files: ElectrochemicalGasSensor.py, ads1115.py and
lmp91000.py.
3. Run the first example
This is the module's electrochemical-bridgeBoard.py example. It creates the
sensor at 0x30, stops with an error if the board does not answer, and prints a
reading every 2.5 seconds. Change scl and sda if you wired other pins.
Where the example's comments mention address jumpers on the back of the board,
this board uses the three-position ADDRESS switch on its top side instead.
# FILE: electrochemical-bridgeBoard.py
# AUTHOR: Fran Fodor @ Soldered
# BRIEF: Single sensor PPM reading example for the ATtiny404 bridge board revision,
# which allows daisy-chaining multiple boards on one I2C bus.
# LAST UPDATED: 2026-07-23
# Connecting diagram:
#
# Qwiic------------------------>Qwiic
#
# Note: on this board revision, LMPEN is hardwired to GND, so there's no
# config_pin to set - it's ignored whenever adc_addr falls in the bridge
# range (0x30-0x37). Set the desired address using the jumpers on the back
# of the board before powering it on.
from machine import I2C, Pin
import time
from ElectrochemicalGasSensor import ElectrochemicalGasSensor, SENSOR_O3
# Initialize I2C
i2c = I2C(0, scl=Pin(22), sda=Pin(21))
# (address = 0x30 + jumper offset, giving a range of 0x30-0x37).
# Any additional boards on the same bus just need a different jumper
# setting, same as twoSensors.py does for legacy boards with 0x49/0x4A/0x4B.
sensor = ElectrochemicalGasSensor(SENSOR_O3, i2c, adc_addr=0x30)
# -------------------------------------------------------------------------
# Setup
# -------------------------------------------------------------------------
print("Electrochemical Gas Sensor - ATtiny Bridge Board Example")
if not sensor.begin():
print("ERROR: Can't init the sensor! Check connections and jumper address!")
while True:
time.sleep_ms(100)
print("Sensor initialized successfully!")
# -------------------------------------------------------------------------
# Main loop
# -------------------------------------------------------------------------
while True:
reading = sensor.getPPM()
# If PPB is more relevant for your sensor, use:
# reading = sensor.getPPB()
print("Sensor reading: {:.5f} PPM".format(reading))
time.sleep_ms(2500)
🔗Open the complete example
Examples/electrochemical-bridgeBoard.py at commit 623e1e6
4. Check the result
When the board answers, the shell starts with:
Electrochemical Gas Sensor - ATtiny Bridge Board Example
Sensor initialized successfully!
After that, a line Sensor reading: followed by a value with five decimals
and PPM arrives every 2.5 seconds.
If you see ERROR: Can't init the sensor! Check connections and jumper address!
instead, the board did not answer at 0x30.
5. If it does not work
Continue with Troubleshooting and retry this smallest example after each change.