Hardware Details
The SGX-4SO2 cell produces a small current that rises with the SO2 concentration. The LMP91000 analog front end biases the cell and turns that current into a voltage, using a 2.5 V reference on the board. The ADS1115 converts the voltage to a 16-bit number. An ATtiny404 microcontroller with factory firmware drives both chips over its own I2C bus and answers your controller as one I2C device on the Qwiic bus.
Key specifications
| Specification | Value |
|---|---|
| Interface | |
| Interface | I2C (Qwiic), analog |
| Qwiic compatible | Yes |
| I2C address default | 0x30 |
| I2C address changeable | Yes, 0x30 to 0x37 by switch |
| Connectors | 2x Qwiic, 2.54 mm headers |
| Breadboard compatible | No |
| Power | |
| Supply voltage | 3.3 V (no regulator) |
| Logic level | 3.3 V only |
| Other | |
| Gas | Sulphur dioxide (SO2) |
| Gas cell | SGX-4SO2, electrochemical |
| Measurement range | 0 to 20 ppm; maximum overload 100 ppm |
| Cell output signal | 400 ± 100 nA per ppm |
| Resolution | 0.1 ppm typical (electronics dependent) |
| Response time | T90 under 30 s |
| Accuracy | Repeatability under ±2% SO2 equivalent; linear within ±5% up to 20 ppm |
| Operating conditions | -30 to 50 °C, 15 to 90% RH (non-condensing), 800 to 1200 mbar |
| Expected cell life | Over 24 months in air |
| Analog front end | Texas Instruments LMP91000 |
| ADC | Texas Instruments ADS1115, 16-bit |
| Bridge MCU | Microchip ATtiny404 (factory firmware) |
| Dimensions | 38 x 38 mm |
The gas cell's performance figures apply at 20 °C, 50% RH and 101 kPa.
Pinout

The board has two I2C buses. Bus 1 (SDA1, SCL1, and both Qwiic connectors) is the one your controller uses. Bus 2 (SDA2, SCL2) runs between the ATtiny404, the LMP91000 and the ADS1115.
| Pin marking | Pin name | Description |
|---|---|---|
3V3 | Power | 3.3 V supply input, shared with both Qwiic connectors |
GND | Ground | Ground |
SDA1, SCL1 | I2C bus 1 | The bus your controller talks on; also on both Qwiic connectors |
SDA2, SCL2 | I2C bus 2 | The board's internal bus between the ATtiny404, the LMP91000 (address 0x48) and the ADS1115 |
VOUT | Analog out | The LMP91000's analog output, the voltage the ADC measures |
ALERT | Control | The ADS1115's ALERT pin |
LMPEN | Control | The LMP91000's enable line, pulled to GND by a 10 kΩ resistor on the board and also connected to the ATtiny404 |
AIN1, AIN2, AIN3 | Analog in | The ADS1115's other three inputs, free for your own analog signals. The Arduino and MicroPython libraries read only VOUT (AIN0), so they give no readings from these inputs. |
UPDI | Programming | The ATtiny404's programming pin, on the side header with 3V3 and GND |
Voltage and logic levels
| Connection | Supported voltage | Notes |
|---|---|---|
3V3 pins and Qwiic | 3.3 V | No regulator: the headers and both Qwiic connectors share one 3.3 V supply |
I2C (SDA1, SCL1) | 3.3 V logic | 10 kΩ pull-ups to 3.3 V, removable with JP5 |
Power the board from 3.3 V only, and use a controller with 3.3 V I2C logic.
Dimensions
The board measures 38 x 38 mm. It has four 3.2 mm mounting holes.
Jumpers
The ADDRESS switch, a three-switch DIP block, sets the board's I2C address from 0x30 to 0x37. Pass the same address to the library.
| Jumper | Default | Function |
|---|---|---|
| ADDRESS switch 1 to 3 | Address 0x30 | I2C address of the board, 0x30 to 0x37 |
| JP1 | Closed | Connects the analog ground (AGND) to GND. Cut it to separate them. |
| JP2 to JP4 | JP2 closed, JP3 and JP4 open | ADS1115 address on bus 2: JP2 ties ADDR to 3V3 (0x49), JP3 to SDA2 (0x4A), JP4 to SCL2 (0x4B). Leave as shipped (see the warning below). |
| JP5 | Closed | Connects the 10 kΩ pull-ups on SDA1 and SCL1. Cut it to remove them. |
| JP6 | Closed | Connects the 10 kΩ pull-ups on SDA2 and SCL2. Cut it to remove them. |
Leave JP2 to JP4 as shipped: JP2 closed, JP3 and JP4 open. The board's factory firmware reads the ADS1115 for you, and it is not confirmed that the firmware finds the ADC at 0x4A or 0x4B, so moving the ADC address with JP3 or JP4 may stop the board from giving readings.
If you do change them, close only one of JP2, JP3 and JP4. All three connect to the same ADDR pin, so two closed jumpers short 3V3 to SDA2, 3V3 to SCL2, or SDA2 to SCL2, depending on which pair you close.